Tuotenumero: 95252
Savun ja lämmön poistoon + normaalin ilmanvaihto
Sivulle puhaltava
400°C / 120 min (F400/120, F400/90, F300, F200)
Normaali ilmanvaihto jatkuvalla toiminnalla jopa 120°C, pysähdyksissä jopa 80°C
Huoltokytkinsarja
Sopii käytettäväksi rannikkoalueella
Lumikuormaluokka SL 1000
Laaja valikoima lisätarvikkeita
Testattu EN 12101-3 mukaan LGAI Barcelonassa
CE-sertifikaatti EN 12101-3
1~ (koot 355 ja 450) tai 3~, 50/60 Hz
Tehokkaat EC-moottorit
Nopeudensäätö 0-10V
Ohjattavissa Modbus:illa
Palotila
DVG-EC-radiaalipuhaltimet ovat tarkoitettu tulipalon kuumien savukaasujen poistamiseen jopa 400 °C/120 min (F400/120, F400/90, F300, F200) sekä normaaliin päivittäiseen ilmanvaihtoon lämpötiloissa, jotka voivat olla jopa 120 °C jatkuvassa käytössä tai jopa 80 °C:ssa seisokissa.
Kotelo on valmistettu meriveden kestävästä alumiinista. Pohjalevy ja siipipyörä, jossa on taaksepäin kaartuvat siivet, on valmistettu sinkillä pinnoitetusta teräksestä. Tasapainotettu dynaamisesti ISO 1940 T1 – laatuluokan G6,3 mukaisesti.
Voimanlähteenä on korkean hyötysuhteen EC-moottori. Liitäntä 1 ~ (koot 355, 450) ja 3 ~ virtalähde. Moottorin jäähdytys tapahtuu raittiilla ilmalla.
EC-säätimellä varustettu moottorin lämpösuoja esiasennettu tehtaalla
. Huoltokytkinsarja sijaitsee kotelon ulko-osassa.
Tulipalon sattuessa kaikkien suojalaitteiden täytyy olla poiskytkettynä täyden toiminnan takaamiseksi.
Tuote | ||
---|---|---|
Kauppanimi | Systemair | |
Tuotteen nimi | DVG-H 450EC/F400 |
Ecodesign | ||
---|---|---|
ErP - yhteensopivuus | 2016/2018 | |
Yksikköluokka | NRVU | |
Ohjaus | Sisäänrakennettu VSD | |
Yksikön tyyppi | UVU | |
Lämmönvaihdintyyppi | Ei mitään | |
Lämpötilasuhde UVU | Ei sovellettavissa | |
qv nom | 1,111 | m³/s |
P nom. | 0,922 | kW |
Ps nom | 393 | Pa |
Puhallintehokkuus | 47,4 | % |
Ulkoinen vuoto | 0 | % |
Äänentehotaso LWA | 88 | dB(A) |
Nimellisdata | ||
---|---|---|
Jännite (ominais) | 230 | V |
Taajuus | 50 | Hz |
Vaihe(et) | 1~ | |
Ottoteho | 930 | W |
Nimellisakseliteho (P2) | 0,8 | kW |
Syöttövirta | 4 | A |
Siipipyörän nopeus | 1 450 | r.p.m. |
Ilmavirta | max 1 722 | L/s |
Kuljetetun ilman maksimilämpötila, 120 min | 400 | °C |
Kuljetetun ilman lämpötila | max 120 | °C |
Kuljetetun ilman maksimilämpötila kierroslukusäädössä | 120 | °C |
Äänidata | ||
---|---|---|
Äänenpainetaso 10 m (vapaakenttä) | 60 | dB(A) |
Äänenpainetaso 4 m (vapaakenttä) | 67 | dB(A) |
Suojaus/luokitus | ||
---|---|---|
Kotelointiluokka, moottori | IP54 | |
Eristysluokka | F |
Mitat ja painot | ||
---|---|---|
Kanavan mitta; pyöreä, sisään | 400 | mm |
Kanavan mitta; pyöreä, ulos | 400 | mm |
Paino | 53 | kg |
Muut | ||
---|---|---|
Kanavaliitoksen tyypit | Pyöreä | |
Moottorityyppi | EC |
Symbol | Description | ||||
G1 |
Fan DVG-EC |
||||
G2 |
EC controller - terminals prewired with connection box on the casing |
||||
G3 |
Service switch ON-OFF, 6 pole + 1xNC |
||||
F1 |
Fault relay |
||||
F2 |
Analog input for set value / speed setting |
||||
F3 |
Potentiometer for speed setting |
||||
F4 |
External sensor |
||||
F5 |
Speed output |
||||
F6 |
FIRE mode (open = FIRE) |
||||
F7 |
Start /Stop switch (open = stop) |
||||
F8 |
Modbus |
||||
E1 |
Power supply - connection in G3 |
||||
Max. cable crosssection: 2,5 mmq (4 mmq without core end sleeves) |
|||||
Max. cable diameter: 13 mm |
|||||
Cable gland on supply side included: 1xM20x1,5 |
|||||
Possible to install additional cable glands 1xM20x1,5, 1xM16x1,5 |
|||||
E2 |
Control cables - connection in G2/connection box on the casing |
||||
Max. cable crosssection: 1,5 mmq, recommended 0,75 mmq, max. cable diameter: 13 mm |
|||||
Cable glands on the connection box: 2xM20x1,5 for control cables |
|||||
2 cable inserts with 3x5 mm hole enclosed for thinner control cables alternatively |
|||||
Eventual protecting tube for control cables not enclosed |
|||||
E3 |
EC-Motor pre-wired |
||||
Marking |
Terminal No. |
Description |
|||
Mains supply |
PE |
1 |
PE connection |
||
N |
2 |
Neutral |
|||
L |
3 |
Supply voltage 1~ 230V/50-60Hz |
|||
Fault relay |
NC |
4 |
Normally close |
||
COM |
5 |
Common connection; contact rating 250V/5A |
|||
NO |
6 |
Normally open |
|||
User interface |
An1 |
7 |
Analog input 1; set value 0-10V; R >= 1kΩ |
||
GND |
8, 12, 14 |
I/O ground |
|||
Pot |
9 |
Potentiometer output (3 wires) |
|||
+5V |
10 |
+5V +/-5% / 10mA for potentiometer |
|||
An2 |
11 |
Analog input 2 for external sensor |
|||
+24V |
13, 16, 19 |
+24V +/- 5% DC (unregulated) voltage / Imax 40 mA |
|||
Speed |
15 |
Digital output; speed output PWM signal |
|||
f ~ 1,1 kHz; NPN open collector output |
|||||
Fire |
17 |
Digital input; FIRE mode |
|||
enabling function - open pin |
|||||
disabling function - bridge to +24V |
|||||
Start/Stop |
18 |
Digital input; start/stop |
|||
start - bridge to +24V |
|||||
stop - open pin |
|||||
A |
20, 22 |
Bus connection RS485 - A; MODBUS RTU |
|||
B |
21, 23 |
Bus connection RS485 - B; MODBUS RTU |
|||
Motor connection |
PE, U, V, W |
24, 25, 26, 27 |
Motor pre-wired |
A | B | G | ød1 | ød2 | ød3 | nxM | ød4 | øD | E | H1 | H | |
DVG-H 400, 450 |
668 |
535 |
854 |
286 |
379 |
438 |
6xM8 |
12 |
400 |
240 |
30 |
650 |
DVG-EC radial fans are intended for the extraction of hot flue gases in the case of fire up to 400 degrees/120 min (F400/120, F400/90, F300, F200), as well as for the normal daily ventilation of medium with temperature up to 120°C in continuous operation and up to 80°C in standstill.
The base plate with inlet cone is made of pre-galvanized steel sheet. The outer casing consists of seawater-resistant aluminium parts. Bird protection grill is a part of casing. The fan has a backward curved radial impeller made of pre-galvanized steel (sizes 355, 450), respectively from steel, welded and galvanized. With taper bush that makes service easier and secured bolted joint directly assembled on the motor shaft. Dynamically balanced according to ISO 1940 T1 quality class G6,3.
Driven by an EC (electronically commutated) high efficiency motor. Connection to 1~ (sizes 355, 450) respectively 3~ power supply. Cooling of the motor with ambient air from the top of casing in underpressure system. Thermal protection of motor by EC controller, factory pre-set. Service switch serial outside on the casing. Flange connection according to dimension sketch.
In case of fire switch to fire mode and bridging of motor protective devices is necessary. Tested according to EN 12101-3 at LGAI, Barcelona. CE-Certification according to EN 12101-3 by BSI, UK.
Asiakirjan tiedostonimi | Asiakirjan tiedostotyyppi | |
---|---|---|
DVG_EC_E8301_19_01_2017.pdf | Esite | |
INSTRUCTION_EC_1PHASE_CONTROLLER_20_12_2016_ V2_2.PDF | Ohjekirja | |
IMO_DVG_EN_19_05_2015_AM_23_12_2015_FI.PDF | Ohjekirja | |
CERTIF_DVV_XS_XL_DVAX_DVG_BKF_2015_0086_CPR_597958.PDF | Sertifikaatti | |
Certif_DVV_DVAX_DVG_BKF_2015_Kitemark_KM_646474.pdf | Sertifikaatti | |
DVG_H_450_EC_M1_10_03.dxf | CAD-tiedosto | |
I058AA_06_DVG_F400_DOP_25_07_2017.PDF | Deklaraatio |